How To Change A Battery In A Timex Watch

• Here is your watch! Actually, this one is mine. Yours is the ane with the dead battery. My battery was dead, non likewise long ago, just I replaced it, and now you can, too!

• Your first job is to remove the watch band, which has flanges that overlap the back plate.

• But wait! The scout band isn't quite what it seems. On the side of this sentinel, there are what appear to be screw heads holding on the band. These are not screw heads, they're just decorative. Instead, you must use a screwdriver or other sparse blade to compress the spring pins and remove the band.



• Remove the back plate by unscrewing the four small phillips-caput screws at the corners of the back plate.

• Put them in a basin, or somewhere safety!

• Remove the metallic dorsum plate.

• Yay, you got the back off!

• Next, the entire watch body tin be lifted out of the example. Practice that.

• Side by side, go alee and use tweezers to remove that sticker. Set it aside upside-down to be re-applied later.

• Finally, insert a thin-bladed screwdriver or spudger in the slot indicated by the royal circle (2d picture), and slide it up and to the right to release ane catch holding the battery in.

• You should be able to lift the whole "meat" of the watch out of the case. Do that.

• Remarkably, the bombardment doesn't just come out of the back. We accept to disassemble the "sandwich".

• There are a whole bunch of metallic straps that run around the edge, but but 5 of them engage with the top half; these need to be released.

• You lot tin can use a spudger or screwdriver for this, only I institute that a fingernail worked just as well, maybe better.

• Remove the top half of the sandwich, and flip it over.

• You lot need to release the metal cover that holds the battery in. At the location indicated by the purple circle, use a screwdriver (a fair corporeality of force is required) to lift/push/release the edge of the cover from the plastic cleat that it'south wrapped around.

• In this moving-picture show, the embrace has already been released.

• At present, flip it over.

• Yay! the bombardment is out.

• Replace the bombardment with a new one.

• Follow the preceding steps in reverse until you lot're set up to put the back plate on.

• At this betoken, the picket might be running and set up to go. If so, you can skip this "Reset the watch" step, and simply reassemble.

• Before putting the back of the sentinel on, you'll need to follow the instructions on the sticker, and "curt" the two "pads".

• 1) The term "short" refers to creating an electrical connection, sometimes known as a "short-circuit", between two points.

• 2) The term "pads" refers to electrical contacts.

• On the sticker (in the photograph above), you volition meet an pointer (really more of a minor triangle) at the lower right of the sticker, pointing to 2 round metallic contacts, or "pads". In gild to reset the spotter, I believe yous will need to create a "short" by touching both of these pads with a conductive object.

• A short piece of copper wire would work, or nearly annihilation else that's conductive. Let me see… Actually, if you took any unplugged appliance, you could probably use i of the prongs of a 110VAC plug to bridge these. (Reiterating: Non WHILE Information technology'South PLUGGED IN.) Maybe information technology would be safer to use a fork, spoon, or conductive screwdriver.

• Complete reassembly by screwing on the back plate and reattaching the watch band.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Embed this guide

Cull a size and copy the lawmaking below to embed this guide every bit a small widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/Timex+Ironman+Battery+Replacement/134510

Posted by: brownarand1988.blogspot.com

Share this post